- 667MHz Xilinx XC7Z010/20 ARM Cortex-A9 Processor with Xilinx 7-series FPGA logic
- 512MB DDR3, 4GB eMMC, 16MB QSPI Flash
- On-board Gigabit Ethernet PHY
- 1.27mm pitch 180-pin Stamp Hole Expansion Interface
- Ready-to-Run Linux 4.14
- Supports -40 to +85 Celsius Extended Temperature Operation for Industrial Applications 

MYIR is a Xilinx Alliance Member, welcome to use MYIR's Xilinx products!
We also offer custom design services, welcome your inquiry!

http://www.xilinx.com/alliance/memberlocator/1-2wv1bc.html

The MYC-Y7Z010/20-V2 CPU Module is an industrial-grade System-on-Module (SoM) based on Xilinx Zynq-7000 family SoC available for either the XC7Z020 or XC7Z010 version. It has integrated the Zynq-7020 or Zynq-7010 device, 512MB DDR3 SDRAM, 4GB eMMC, 16MB quad SPI Flash, a Gigabit Ethernet PHY and external watchdog on board and provides 1.27mm 180-pin stamp-hole (Castellated-Hole) expansion interface to allow a large number of I/O signals for ARM peripherals and FPGA I/Os to be extended to your base board. The module is ready to run Linux and supports wide working temperature ranging from -40 to +85 Celsius which is ideal for industrial embedded applications.

MYC-Y7Z010/20-V2 CPU Module

MYIR provides a development board MYD-Y7Z010/20-V2 for evaluating the MYC-Y7Z010/20-V2 CPU Module, which employs the MYC-Y7Z010/20-V2 as the controller board by populating the CPU Module on its base board through 1.27mm pitch 180-pin stamp-hole (Castellated-Hole) interface. The base board has extended a rich set of peripheral interfaces including serial ports, USB Host port, three Gigabit Ethernet ports, CAN, TF card slot, JTAG, etc. One 2.54mm pitch 2 x 25-pin expansion header is on the base board to let more GPIOs available for further extension.

MYD-Y7Z010/20-V2 Development Board 

Features

Mechanical Parameters

• Dimensions: 75mm x 50mm (10-layer design)
• Power supply: 5V
• Working temp.: -40~85 Celsius (industrial grade)

SoC

• Xilinx XC7Z010-1CLG400I (Zynq-7010) / XC7Z020-1CLG400I (Zynq-7020)
  - 667MHz dual-core ARM® Cortex™-A9 MPCore processor (up to 866MHz, for XC7Z010 or XC7Z020)
  - Integrated Artix-7 class FPGA subsystem
  with 28K logic cells, 17,600 LUTs, 80 DSP slices (for XC7Z010)
  with 85K logic cells, 53,200 LUTs, 220 DSP slices (for XC7Z020)
  - NEON™ & Single / Double Precision Floating Point for each processor
  - Supports a Variety of Static and Dynamic Memory Interfaces

Memory

• 512MB DDR3 (2 x 256MB, 32-bit)
• 4GB eMMC
• 16MB QSPI Flash

Peripherals and Signals Routed to Pins

• 10/100/1000M Ethernet PHY (YT8521SH)
• External watchdog
• Three LEDs
  - One red LED for power indicator
  - One green LED for FPGA program done indicator
  - One flashing green LED for system indicator
• 1.27mm pitch 180-pin Stamp Hole Expansion Interface brings out below signals:
  - One Gigabit Ethernet
  - One USB
  - Two Serial ports
  - Two I2C
  - Two CAN BUS
  - Two SPI
  * Serial ports, I2C, CAN and SPI signals in PS part can be implemented through PL pins via Emio.
  - Two ADC (16-channel ADC brought out through PL pins)
  - One SDIO

OS Support

• Linux 4.14

Other MYIR's Xilinx Products

http://www.myirtech.com/xilinxseries.asp

VECP Starter Kit (Vision Edge Computing Platform based on Zynq UltraScale+ ZU3EG MPSoC)

MYD-CZU3EG/4EV/5EV Development Board (MYC-CZU3EG/4EV/5EV CPU Module as core board)

FZ3 Card (Deep Learning Accelerator Card based on Zynq UltraScale+ ZU3EG MPSoC)

Z-turn Board Single Board Computer (based on Zynq-7010 / 7020)

Z-turn Lite Single Board Computer (based on Zynq-7007S / Zynq-7010)

MYD-C7Z010/020 Development Board (MYC-C7Z010/020 CPU Module as core board)

MYD-C7Z015 Development Board (MYC-C7Z015 CPU Module as core board)