Developers and makers are invited to discover the flexibility of a low-power programmable gate array. The Intel® Cyclone® 10 LP Evaluation Kit provides an easy-to-use platform for evaluating Intel® Cyclone® 10 LP FPGA technology and Intel Enpirion® regulators.

With this evaluation board, you can :

•     Develop designs for Intel® Cyclone® 10 LP FPGA devices
•     Bridge to  functions or devices via Arduino UNO R3 shields, PMOD , GPIO or Ethernet connectors
•     Measure key Intel Cyclone® 10 LP FPGA power supplies
•     Reuse the kit's PCB schematic & design files to start your design quickly

Whether you are an FPGA developer, software developer, maker, seasoned IoT developer, coding newbie, or just curious about FPGAs, we hope your experience with the Intel Cyclone® 10 LP FPGA kit is both informative and fun.

• Intel® Cyclone® 10 LP FPGA
  • P/N: 10CL025YU256I7G with 25K LEs
• Intel® MAX® 10 FPGA, pre-programmed System Manager ASSP functions (Not reprogrammable by the user)
  • On-board USB Blaster II
  • SystemMAX  controller
    • Programmable clock adjustment
    • Current measurement for key Intel Cyclone 10 LP FPGA power rails
    • Arduino Analog input and conversion to digital signals
  • P/N: 10M08SAU169C8G
    • 8K LEs, Single Power Supply, 1 ADC with 9 input channels
• Enpirion point-of-load Synchronous Buck Regulators with Integrated Inductors:
  • EN5339QI, 3A
  • EN5329QI, 2A
  • EP5358LUI, 600mA 2 pieces
• HyperRAM*
  • 128Mbit 8-bit width HyperRAM memory
  • 100 MBs throughput @ only 400 LE's and 12 I/O
  • Open Core license available for evaulation
  • HyperBus Memory Controller IP by Synaptic Labs
• 10/100/1000Mbps Ethernet
  • Intel XWAY PHY11G PEF7071
  • RGMII Interface to Intel Cyclone 10 LP FPGA (as MAC),
    • Triple speed ethernet MAC supported from Quartus Prime version 17.1 onwards
  • MDC/MDIO as management interface
  • RJ-45 for Ethernet Cable
• 12-pin Digilent Pmod* Compatible connector
  • Refer  Pmod* Compatible expansion cards
• Arduino Interface
  • Compatible with Arduino UNO R3
  • Arduino Shields can be used on this Arduino Interface
• User GPIOs
  • 2x20 expansion GPIO header with 36 GPIO signals brought out to a 100mil header
  • Single-end IO with 3.3 VCCIO
• LED
  • Blue Power LED x1
  • Yellow Configuration LED x1
  • Green User LEDs x4
• Push Button
  • FPGA Reconfiguration Push Button x1
  • FPGA Reset Push Button x1
  • User Push Buttons x4
• 4-bit DIP Switch
  • 1-bit Virtual JTAG bypass
  • 3-bit User DIP Switch
• Configuration
  • On-board USB Blaster II Programming
  • External 2x5 JTAG Header
  • AS x1 configuration via on board Flash (EPCQ64)
• Clock
  • Fixed 50MHz clock to Intel Cyclone 10 LP FPGA and Intel MAX 10 FPGA
  • 125MHz Ethernet Clock to Intel Cyclone 10 LP FPGA (Programmable)
  • 50MHz HyperRAM Clock to Intel Cyclone 10 LP FPGA (Programmable)
  • Programmable clock to Intel Cyclone 10 LP FPGA
• Power
  
  • USB or Adaptor powered
    • USB port shared with on-board USB Blaster II Mini-B Connector
    • AC-DC (5V) adaptor which is not be shipped with kit
  • Intel Cyclone 10 LP FPGA Power Measurement Capability
    • Intel MAX10 FPGA ADC to measure current for specified Intel Cyclone 10 LP FPGA power rails
    • Voltage and current manual measurement for other Intel Cyclone 10 LP FPGA power rails

 

Intel® Cyclone® 10 LP FPGA Evaluation Kit - Block Diagram

▶ Resources