CR00140-02-K1C 이미지 확대 보기
  • CR00140-02-K1C

CR00140-02-K1C

공유
짧은설명
Motor Control Development Kit with AMD Zynq™ 7020-1C SoC Module
판매가
1,166,000 <관세ㆍ부가세 포함>
구매제한
옵션당 최소 1개
구매혜택
할인 : 적립 마일리지 :
배송비
154,000원
택배
방문 수령지 : 경기도 성남시 중원구 사기막골로 99 성남센트럴비즈타워2차 B동 913호
상품코드
1000619218
제조사
Trenz Electronic
CR00140-02-K1C
0
총 상품금액
총 할인금액
총 합계금액

상품상세정보

Product information "Motor Control Development Kit with AMD Zynq™ 7020-1C SoC Module"

The predecessor of this article is CR00140-02-K1B. All changes are in the Product Change Notification (PCN).

The Trenz Electronic motor control development kit CR00140-02-K1C includes a CRUVI motor driver module CR00140-02, a carrier board TEB0707-02 and a TE0720-04-61C33MA module with AMD/Xilinx Zynq™ XC7Z020-1CLG484C SoC including a heat sink. Supplied with a universal plug-in power supply with four adapters, a DC motor including cable for CRUVI CR00140 and an 8 GB micro SD card.

Support Package for Motor Control Development available at MathWorks.

The Module: CR00140-02

The Trenz Electronic CR00140 is a CRUVI motor driver module. It supports motors with up to 4 phases up to 40V. 

Key Features

On Board

  • MAX 10 CPLD
  • 2 phase current measurement
  • DC_LINK voltage measurement
  • 4 x LEDs (2 power indicator, 2 user)
  • 2 x Pushbutton

Interface

  • 4 phase screw terminal motor connector
  • CRUVI for control
    • 1 x high speed connector
  • 6 x 1 pin header for single ended sensors
  • 5 x 2 pin header for differential sensors

Power

  • Screw terminal for up to 40V DC motor supply

Dimension

  • 68.35 mm x 131 mm

The Module: TE0720-04-61C33MA

The Trenz Electronic TE0720-04-61C33MA is a SoC module integrating a AMD/Xilinx Zynq™ 7020, a Gigabit Ethernet transceiver, 1 GByte DDR3L SDRAM, 32 MByte Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/O's is provided via rugged high-speed stacking strips.

Key Features

  • AMD/Xilinx Zynq™ XC7Z020-1CLG484C
  • Rugged for high shock and vibration
  • ARM dual-core Cortex-A9 MPCore
  • 10/100/1000 tri-speed Gigabit Ethernet transceiver (PHY), SGMII accessible on a board-to-board connector
  • USB 2.0 high speed ULPI transceiver
  • 32-bit wide 1 GByte DDR3L SDRAM
  • 32 MByte QSPI Flash memory (for configuration and operation)
  • 8 GByte e.MMC (optional up to 32 GByte)
  • Plug-on module with 2 x 100-pin and 1 x 60-pin Razor Beam High-Speed hermaphroditic Terminal/Socket Strips (regular 4 mm)
  • 152 FPGA I/O's (75 LVDS pairs possible) and 14 MIO's available on board-to-board connectors
  • On-board high-efficiency DC-DC converters
    • 4.0 A x 1.0 V power rail
    • 1.5 A x 1.5 V power rail
    • 1.5 A x 1.8 V power rail
  • System management and power sequencing
  • eFUSE bit-stream encryption
  • AES bit-stream encryption
  • Valid MAC Address and 2K serial EEPROM
  • SHA-256 authentication chip with unique serial number
  • RTC, temperature compensated
  • 3 user LEDs
  • Evenly-spread supply pins for good signal integrity
  • 4 x 5 cm form factor

The Baseboard: TEB0707-02

The Trenz Electronic TEB0707 is a carrier board for 4 x 5 Trenz Electronic modules. It provides three high speed and one low speed CRUVI extension connectors. For more information, please refer to the CRUVI B2B Connectors.

The TEB0707 is integrated with an Intel® MAX® 10 FPGA as system controller and is equipped with a Micro USB2.0 socket with FTDI to JTAG/UART solution, RJ45 LAN socket, USB A socket, microSD card socket, user LEDs, push buttons and DIP switches for controlling the SoM.

Key Features

Modules

  • 4 x 5 Trenz Electronic modules

RAM/Storage

  • EEPROM (FTDI configuration)

On Board

  • Intel® MAX® 10 FPGA
  • FTDI FT2223
  • 6 x user LEDs (3 x green, 3 x red)
  • 2 x status LEDs
  • DIP switch
  • Push buttons

Interface

  • Gigabit RJ45 LAN socket
  • MicroSD card socket
  • Micro USB2.0 socket
  • USB A socket
  • 3 x High Speed CRUVI B2B connectors
  • 1 x Low Speed CRUVI B2B connector
  • 4 x Jumpers

Power

  • 5V input power supply

Dimension

  • 135 mm x 68 mm

Other assembly options for cost or performance optimization plus high volume prices available on request.

Scope of Delivery

  • 1 x CR00140-02 CRUVI Motor Driver Module
  • 1 x TE0720-04-61C33MA MPSoC Module with AMD/Xilinx Zynq™ XC7Z020-1CLG484C
  • 1 x TEB0707-02 Carrierboard for Trenz Electronic 4 x 5 Modules
  • 1 x Pre-installed heatsink for TE0720
  • 1 x BLY172D-24V-4000-1250SI Brushless DC Motor from Anaheim Automation
    • Rated Voltage 24V
    • Rated Speed 4000rpm
    • Rated Power 53W
    • Including encoder, 1250 count per rev, index function (single ended connection)
  • 1 x Universal plug power supply with 4 adapters
  • 1 x 8 GB Class 4 microSDHC-Card
  • 1 x Cable for CR00140

Additional Information

All modules produced by Trenz Electronic are developed and manufactured in Germany.

The online pictures of this product are not a legally binding offer, but are symbol pictures for illustration and presentation only.

 

Related links to "Motor Control Development Kit with AMD Zynq™ 7020-1C SoC Module"

배송안내

 결제일로부터 1~3주 안에 배송됩니다.

 제조사 재고가 부족하여 3주 안에 배송이 어려울 경우 메일로 안내해 드리니 참고하시기 바랍니다.

교환 및 반품안내

 본 상품은 해외 재고 상품으로 기본적으로 교환 및 반품 처리가 어렵습니다.

 상품에 따라 교환 및 반품 처리가 가능한 경우 비용이 수반되며 이니프로 고객센터에 연락하여 처리하시기 바랍니다.

환불안내

 본 상품은 해외 재고 상품으로 기본적으로 환불 처리가 어렵습니다.

 상품에 따라 환불이 가능한 경우 비용이 수반되며 이니프로 고객센터에 연락하여 처리하시기 바랍니다.

AS안내

 제조사별로 A/S정책이 상이하니 하단 고객센터로 문의 주시기 바랍니다. 

이미지 확대보기CR00140-02-K1C

CR00140-02-K1C
  • CR00140-02-K1C
닫기

비밀번호 인증

글 작성시 설정한 비밀번호를 입력해 주세요.

닫기

장바구니 담기

상품이 장바구니에 담겼습니다.
바로 확인하시겠습니까?

찜 리스트 담기

상품이 찜 리스트에 담겼습니다.
바로 확인하시겠습니까?

상단으로 이동