The Trenz Electronic Starter Kit TE0729-03-62I63MAS consists of a TE0729 module on a TEB0729 carrier board with an XMOD FTDI JTAG adapter including mounted heatspreader. Additionally accessories are a 5V power suppy with four adapter, two VG96 connectors (DIN 41612), a 16 GB microSD card and an USB cable.

The Module: TE0729-03-62I63MA

The Trenz Electronic TE0729 is an industrial-grade SoC module integrating a AMD/Xilinx Zynq™ 7020 with a Gigabit Ethernet transceiver, 2 x 100 Mbit Ethernet, 512 MByte DDR3L SDRAM, 32 MByte Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/O's is provided via rugged high-speed stacking strips.

Key Features

• SoC / FPGA
  • Device: AMD/Xilinx Zynq™ XC7Z020-2CLG484I
  • Speedgrade: -2
  • Temperature range: Industrial
  • Package: CLG484I

• RAM / Storage
  • 512 MByte (16-bit) DDRL3 SDRAM
  • 32 MByte QSPI-Flash
  • 8 GByte e.MMC Memory
  • 3 x 2 Kbit serial EEPROM with EUI-48 Node Identity

• On Board
  
  • Dual-core ARM Cortex-A9 MPCore™ with CoreSight™
  • System Management
  • USB 2.0 High-Speed ULPI transceiver with full OTG support
  • eFUSE bit-stream encryption
  • AES bit-stream encryption
  • Temperature compensated RTC (real-time clock)
  • User LED

• Interface
  • 136 FPGA I/O's (58 LVDS pairs possible) and 6 PS MIO's available on board-to-board connectors
  • Plug-on module with two 120-pin connectors
  • 1 x 10/100/1000 Mbps Ethernet transceiver PHY
  • 2 x 10/100 Mbps Ethernet transceiver PHYs 

• Power
  • Evenly-spread supply pins for good signal integrity
  • On-board high-efficiency DC/DC converter
  • 4.0 A x 1.0V power rail
  • 1.5 A x 1.5V power rail
  • 1.5 A x 1.8V power rail
  • 1.5 A x 2.5V power rail

• Dimension
  • 5.2 x 7.6 cm
    
    

The Baseboard: TEB0729-03A

The Trenz Electronic TEB0729 carrier board was especially designed and developed for the use of Trenz Electronic module TE0729.

Key Features

• Trenz TE0729 Module Socket (2 x Samtec Connectors, 120 Pins)
• Barrel jack for 5V power supply
• 2 x RJ45 10/100-BaseT Ethernet MagJack with 2 integrated LEDs
• 1 x RJ45 Gigabit Ethernet MagJack with 2 integrated LEDs.
• 2 x Configuration EEPROM's, connected to SoM's I²C interface
• XMOD compatible header to connect the TE0790 USB 2.0 adapter board
• JTAG and UART interface over XMOD header
• MicroSD Card socket, can be used to boot system
• USB 2.0 socket
• 4-bit DIP switch for SoM configuration (SoM's JTAG access and Bootmode)
• VG96 connector soldering-pads J8 for access to SoM's PL-IO-bank-pins, usable as LVDS-pairs
• VG96 connector soldering-pads J9 for access to further interfaces and IO's of the SoM
• 1 x user LED (red)
• 1 x user push-button routed to SoM (Reset function at standard configuration)
• Pin headers to set PL-IO-bank's VCCIO with jumper

TE0790 XMOD FTDI JTAG Adapter (pre-assembled)

XMOD-USB-X is a universal USB adapter with 2 channels based on FTDI FT2232H USB2 HS Interface chip. In the consigned default configuration Port A is JTAG and Port B is a serial interface.

FT2232H port A and B are connected to small on-board programmable CPLD to allow flexible application specific remappings of FT2232H functions into 8 user I/O pins of single XMOD 12 x 8 Module.

Minimum PCB area on base board to support JTAG function: 5 x 10 mm (does not include mounting hole space).

NOTE: This adapter is compatible with AMD/Xilinx Tools!

Key Features TE0790

• XMOD form-factor
  - supported base slots: 6 x 2, 8 x 4, 10 x 6, 12 x 8, 5 x 2, 5 x 3
  - size: 20 x 25 mm
  - M3 mounting hole
• FT2232H
  - Channel B RX/TX LED's (on top, not visible from front)
  - mini-USB connector (more rigid then micro-USB)
  - 93C56 EEPROM
• Lattice XO2-256 CPLD
  - on board programmable using Lattice tools
  - 8 universal I/O pins
  - VCCIO either 3.3 V or user supplied (1.8 V to 3.3 V)
  - Red user LED (front visible)
  - 12 MHz clock from on-board Oscillator
• LDO/DCDC for optional USB power
• Green Power-on LED (front visible)
• User button (front accessible)
• 4 position DIP switch
  - Choose CPLD program mode
  - FTDI EEPROM disable (not implemented in PCB REV 1)
  - Use VIO same as VCC
  - Use VCC from USB

Scope of Delivery TE0729-03-62I63MAS Starter Kit

• 1 x TE0729-03-62I63MA SoC module with AMD/Xilinx Zynq™ 7020 XC7Z020-2CLG484I and sulfur resistant resistors
• 1 x TEB0729-03A carrier board for TE0729 module from Trenz Electronic
• 1 x KK0729-02TE heatspreader especially for TE0729 (mounted)
• 1 x TE0790-03 XMOD FTDI JTAG adapter, AMD/Xilinx compatible (mounted)
• 2 x VG96 Connectors (DIN 41612)
• 1 x 5V power supply with 4000 mA and 4 adapter for UK, US, EU and AU
• 1 x 16 GB class 4 microSDHC card without adapter
• 1 x USB cable, type A to type B mini, 2 meter length
• 4 x bolts M3 x 5 mm, mounted
• 4 x M3 x 12 screws
• 4 x M3 x 4 screws

Additional Information

• Manufacturer's article number: TE0729-03-62I63MAS
• Trenz Electronic Wiki - Starter Kit TE0729
• Support Forum